-
What is a winder？
2019-03-27 2020
Second, the entire base paper is cut into a number of widths that meet user specifications; Third, control the winding diameter of the finished paper roll to meet the factory specifications. Article from Jiangmen Nantian Machinery Manufacturing Co., Ltd.
-
There are several kinds of crafts for slitting machines.？
2019-03-27 2103
Extrusion slittingExtrusion slitting is not common on domestic slitting machines. It consists mainly of pneumatic knives that are synchronized with the material speed and have a material with a certain angle of the bottom roller and convenient conditioning. This slitting method can be used to separate thin plastic films or thicker papers, nonwovens, and the like. It is a convenient method of slitting. It is a development direction of the slitting machine striping method. 3. Flat knife sli
-
How to do the maintenance and maintenance of the slitter？
2019-03-27 2172
Second, use high-quality slitting and cross-cutting knives;Third, the daily maintenance of the slitting machine should be in place. The standard is that lubrication, cleaning, and clearing (no dust, no debris) are in place to ensure that the sliding part of the equipment is in good condition. Article from Jiangmen Nantian Machinery Manufacturing Co., Ltd.
-
What is the reason why the tension of the film winder is too small?
2019-03-27 2059
There is sometimes no tension in the magnetic powder clutch.For this reason, there is a short circuit or poor contact. Check if the input wire is exposed and touch the mechanical body. Check for loose wire connections. Another reason is that the internal magnetic powder has now lost a part of the magnetic properties, and sometimes there is no phenomenon when tension occurs during the application process. In this case, it is considered to replace the new magnetic powder. 3. The magnetic po
-
Four operating requirements of the slitting machine
2019-03-27 2004
The most important performance indicators for fixed length slitting are the cutting accuracy and the consistency of the finished product length. The slitting length can be set continuously. If there is an error in the actual slitting length, it is easy to calibrate by setting parameters. Article from Jiangmen Nantian Machinery Manufacturing Co., Ltd.
-
What are the requirements for the process of the winder?
2019-03-27 2038
In the process of cutting the paper, the paper cutter will inevitably form a slit end face between the two cut papers. In theory, it can be cut into a plane, but in practice, it is often impossible to cut the unevenness. When the paper rolls are interlaced, the two rolls of paper are staggered together, and the width of the cut uneven paper rolls is inconsistent, which may cause trouble in use. The coated whiteboard paper is a coated paperboard having a bright coating on the coated side,
-
Working principle of rewinder PLC controller system
2019-03-27 2081
In the process of user program fulfillment, the rewinder does not change the status and data of the input point in the I/O image area, while other output points and soft devices are in the I/O image area or system RAM storage area. The status and data are subject to change, and the ladder diagrams listed above, the program performance results will work on the ladder diagrams that use the coils or data below; instead, the ladder diagrams below, The status or data of the rewritten logic coil can o
-
Pay attention to the precautions of the use of slitting machine？
2019-03-27 2030
When blowing, first stop the machine and put the paper into the tube, then turn it back on. when blowing, pay attention to the stability of the flash when accelerating. 11, encountered c-class papers to slow down the speed as much as possible to avoid the situation of paper breaks (1200 rpm with 1800 rpm is 5 minutes slower and then the time difference is 7 minutes). 12. For some problems with the paper core of the base paper, pay attention to the proper chuck clamping of the original pap
-
What is the working principle of the winder?
2019-03-27 2288
The working principle of the winder: the paper roll taken from the paper machine is placed on the paper exit frame, the brake device on the paper return frame keeps the paper web with a certain tension, and the paper roll is quickly made when the paper is broken. Move to reduce paper loss. The web is cut to the desired width by a transfer roller and slitting mechanism and then rolled into a roll of paper at the desired tightness and diameter. ? Article from Jiangmen Nantian Machinery Manu
-
How to maintain and maintain the winder？
2019-03-27 1973
pay attention to the voltage of the winder should be stable, otherwise it is easy to burn the motor; pay attention to hygiene, do not let the debris fall between the steel roller and the roller.Article from Jiangmen Nantian Machinery Manufacturing Co., Ltd.